Metal Care Instructions for Cremation Jewelry

General Information:
Always avoid chlorine when wearing your jewelry. Never clean your jewelry with chlorine bleach. Bleach ruins metal via oxidization and turns it black. To be on the safe side, remove your jewelry before doing any household chores. Many common household cleaners have bleach and other chemicals that may adversely affect jewelry. In addition, don’t swim or go in a hot tub wearing fine jewelry because prolonged exposure to chlorine can cause your jewelry to turn black.

Sterling Silver Care:
Sterling silver tarnishes. If possible, store your sterling silver jewelry in a tarnish prevention cloth or bag. The treated cloth slows down the tarnish process and keeps the jewelry from rubbing against harder jewelry that might scratch it. Try to keep your sterling silver jewelry in a cool, dry place. Polishing cloths are an excellent choice for cleaning your sterling silver jewelry. You might read recommendations to use toothpaste to clean sterling silver, but avoid doing that – toothpaste is too abrasive.

Gold-Plated Care:
Gold-Plated jewelry is made by covering sterling silver with a layer of 14K gold. Since the gold is only a layer, it may eventually wear away. This wearing away process is not eligible for warranty replacement. Gold-Plated pieces can be re-dipped by a jeweler. To clean, lightly wipe your gold-plated jewelry with a damp cotton cloth. This will help eliminate any dirt or dust from accumulating on the surface and wearing away the gold layer. Polish cream should not be used on gold-plated items.

Solid 14K Gold Care:
Light tarnish on gold can be removed by using soapy water and a soft bristle brush. A soft toothbrush and some dishwashing liquid also works well. Here is how to do it: Dip the toothbrush in the water and get the bristles into all of the crevices. Then rinse the piece in warm water until the water runs clear. After gentle scrubbing, buff the piece dry with a soft, lint-free cloth to make it shine. You can also use a specially treated cloth or other cleaning jewelry products. If your gold jewelry does not contain colored gemstones you can clean it with an ultrasonic cleaning machine. Finally, if you have a problem with heavy tarnish, please consult a jeweler.


Caring for your Laser Photo Jewelry:
Each piece of Laser Photo Jewelry has been coated with a high-tech, completely transparent nano-ceramic coating which has been electro-magnetically and thermally fused to the pendant. The resulting surface is highly abrasion and tarnish resistant. Should the surface need cleaning, we recommend using a damp, soft cotton or micro-fiber cloth.


PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE FILLING PENDANTS

Filling Instructions for Sterling Silver, 14K Gold-Plated, Solid Gold, and Platinum Pendants:

1) Locate the pendant opening. Depending on the piece, this can be the bail itself (the loop that the chain goes through) or a small, square screw or flathead screw. If pendant has a square screw, use the provided screwdriver; if the screw is flathead, you can open it with a small standard flathead screwdriver available at most hardware stores.

2) Remove the screw and place it carefully aside. Locate the filling “funnel” included in your filling package. It resembles a business card. Fold the card in half on the fold line and place a small amount of fine ash in the center and gently tap it into the pendant opening.

3) Fill the pendant about 90% full, making sure to leave enough room to replace the screw. A toothpick, also provided, can be used to help guide the ashes into the opening.

4) Before replacing the screw back into position make sure that the threads are clean and clear of ashes. Insert the screw and tighten firmly. The tiny rubber gasket on the screw provides a water-tight and airtight seal.

5) When replacing the screw on pendants that open from the bail, pay close attention to the position so the pendant will hang correctly when re-strung on the chain or cord.


Filling Instructions for Stainless Steel Pendants:

1) Locate the pendant opening. Depending on the piece, this can be the bail itself (the loop that the chain goes through) or a small, square screw or flathead screw. If pendant has a square screw, use the provided screwdriver; if the screw is flathead, you can open it with a small standard flathead screwdriver available at most hardware stores.

2) Remove the screw and place it carefully aside. Locate the filling “funnel” included in your filling package. It resembles a business card. Fold the card in half on the fold line and place a small amount of fine ash in the center and gently tap it into the pendant opening.

3) Fill the pendant about 90% full, making sure to leave enough room to replace the screw. A toothpick, also provided, can be used to help guide the ashes into the opening.

4) To permanently seal the pendant, first ensure that the inner threads are clean and clear of all ash. Apply a tiny amount of the provided sealant to the threads on the screw, not the inner threads, and quickly replace the screw.

5) When replacing the screw on pendants that open from the bail, pay close attention to the position so the pendant will hang correctly when re-strung on the chain or cord. 


Instructions for Glass Victorian Lockets:
You can choose to put back-to-back photos or a precious lock of hair of your loved one inside.
Not Recommended for Ashes.

1) Open the locket by unscrewing the lower nut located under the top bail and lay the pendant on a flat surface so that both glass sides are facing up.

2) If filling with a lock of hair, we’ve found that twisting the hair into an infinity sign or number 8 provides a neat and elegant look.